Important Plumbing Tips for Bathtub Installation
Important Plumbing Tips for Bathtub Installation
Blog Article
In this article down the page you can discover lots of wonderful additional info around How to Install a Bathtub Yourself.
Setting up a bath tub isn't exactly brain surgery, however it does need strong plumbing, woodworking, and sometimes, tiling skills. Changing an old tub with a brand-new one is likewise a moderately difficult job. If the old bathtub is conveniently available, the project can relocate rapidly; if you have to open a wall to remove the old bathtub and also place the brand-new bathtub, the task is a lot harder. In either instance, the project is within a residence handyman's skills, although you will need a helper to leave the old bathtub as well as embeded in the brand-new one. Make certain you have certified on your own for the job and are comfortable trying it. Rather than hiring a contractor to take over a halfway-completed task, it is better to consider employing one prior to you start. Opportunities are you may need an expert plumber to make tube connections.
This article will certainly help you install a brand-new bath tub in your shower room if you have actually currently purchased a brand-new bathtub and do not need to change the arrangement of your previous water pipelines.
Your devices and material checklist need to make up the following:
Getting ready for the Setup
First of all, the supporting structure supplied with the bath needs to be fitted (if called for) according to the producer's directions. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is important to make certain that if the faucet includes a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets device to prevent strain on the bathtub.
Fit the flexible faucet ports to the bottom of both faucets utilizing 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make certain you use all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath need to currently be ready to be fitted in its final setting.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installation, after that the first thing you ought to do is detach the water supply. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The process of eliminating the existing taps can be quite bothersome due to the restricted accessibility that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a fabric all set for the staying water that will come from the pipes. Once the supply pipelines have actually been eliminated, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from turning during this procedure. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old sealing compound.
Prior to carrying on to fit the new taps, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Bathtub
Using both wooden boards under its feet, put the bathtub in the needed placement. The wooden boards are useful in uniformly spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 small factors.
The next objective is to ensure that the bath tub is leveled all round. This can be attained by checking the spirit level and readjusting the feet on the tub till the spirit level reviews degree.
To install taps, fit the bottom of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression sign up with; then do the very same for the various other faucet.
Switch on the water and examine all joints and also brand-new pipework for leaks and also tighten them if necessary. Fill the tub and additionally examine the overflow outlet and the typical outlet for leaks.
Lastly, deal with the bath paneling as defined in the manufacturer's instruction manual. Tiling and also sealing around the bath tub ought to wait till the bathtub has been used a minimum of when as this will resolve it into its last placement.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will require a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end gives a link to the current supply pipelines.
If you require to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the installing opening in the bath/basin guaranteeing that the washers are in place in between the faucet and also the sink. Secure the tap in place with the maker offered backnut. Once the tap is safely in place, the supply pipes can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet ports. The former kind needs to be connected to the faucet finishes first, tightening just by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the area where the bathroom fulfills the tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to split a stiff seal, creating the water to pass through the wall between the bath and the tiling, leading to problems with moisture as well as feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your fixtures as well as installations. They are marketed in tubes and also cartridges, and also can securing gaps as much as a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always load the bath tub with water before sealing, to allow for the movement experienced when the bathtub is in use. The sealant can fracture rather very early if you do not think about this motion before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the marketplace. It is a good idea to fit the floor tiles utilizing waterproof or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
I hope you enjoyed our article about Installing A Bathtub. Thank you so much for taking a few minutes to read through our article post. Those who liked our blog entry if you please make sure you remember to share it. Thank you for your time. Kindly come by our site back soon.
Clog issue? Reach out! Report this page